L7812 Voltage Regulator

Specification	Details
Output Voltage	+12V DC
Max Output Current	1.5 Amps
Input Voltage Range	14.5V to 35V DC
Package Type	TO-220 (Through-Hole)
Dropout Voltage	~2.0V
Operating Temperature	0°C to +125°C
Protection Features	Internal Thermal Overload & Short Circuit Protection

Price

₹ 12.71

(Tax included)

बारकोड: 604201

Product Description

The L7812 is a classic three-terminal positive voltage regulator designed to provide a fixed, stable 12V output from a higher-voltage DC source. Part of the legendary L78xx series, it is capable of delivering up to 1.5A of current, making it an essential component for powering 12V relays, fans, sensors, and microcontrollers from unregulated power adapters or battery packs. Housed in the industry-standard TO-220 package, it is easy to mount on breadboards, perf-boards, or dedicated PCBs. With built-in thermal shutdown and current-limiting features, the L7812 is remarkably "bulletproof," protecting itself and your circuit from accidental overloads.

Key Features

Fixed 12V Output: Eliminates the need for external resistors to set the voltage, simplifying your circuit design.
High Current Capability: Can supply up to 1.5A with adequate heat sinking.
Internal Protection: Features safe-area compensation and thermal shutdown to prevent catastrophic failure.
Wide Input Range: Accepts input voltages up to 35V, allowing it to regulate highly unstable DC sources.
Standard TO-220 Package: Easily attached to heat sinks for high-power applications.
Low Noise: Provides a much cleaner DC output than switching regulators, ideal for sensitive analog audio or sensor circuits.

Technical Details

Pin 1 (Input): Unregulated DC voltage (Minimum 14.5V).
Pin 2 (Ground): Common negative terminal.
Pin 3 (Output): Regulated +12V DC.
Quiescent Current: ~5mA.

Prototyping and Engineering Tips from Robogears

The Voltage Gap (Headroom): CRITICAL: The L7812 is a linear regulator. It requires at least 14.5V at the input to maintain a steady 12V output. If your input drops below 14V (e.g., a dying 12V battery), the output will "drop out" and fail to regulate, potentially causing your circuit to reset.
Heat Management: Linear regulators discard "extra" voltage as heat. If you input 24V and draw 1A, the regulator must dissipate 12 Watts (24V−12V)×1A=12W. Without a Heat Sink, the L7812 will get extremely hot and trigger its thermal shutdown within seconds. Always use a heat sink for current draws over 200mA.
Capacitor Requirements: For stability, always place a 0.33µF ceramic capacitor on the input pin and a 0.1µF ceramic capacitor on the output pin, as close to the regulator body as possible. This prevents high-frequency oscillations that can cause voltage ripples.
Reverse Polarity Protection: If there is a chance the input voltage could be cut while the output is connected to a large battery or capacitor, solder a 1N4007 diode between the Output (Anode) and Input (Cathode) pins. This prevents current from flowing backward through the regulator, which can destroy it.
Efficiency Note: If your project is battery-powered and requires high efficiency, consider that linear regulators like the L7812 are inefficient when the input-output voltage gap is large. For battery longevity, a switching "Buck Converter" might be a better choice, though it will be noisier than the L7812.

Package Includes

1 x L7812 Positive Voltage Regulator (TO-220)

Disclaimer: Product images are shown for illustrative purposes only. The branding (ST, TI, etc.) or specific suffix on the part number may vary between batches, but all technical specifications and 12V/1.5A performance standards remain as described.

Safety Warning: Ensure the input voltage does not exceed 35V. The metal tab on the TO-220 package is internally connected to the Ground (Pin 2); if you mount multiple regulators on the same heat sink, ensure they all share the same ground or use insulating mica kits to prevent short circuits. Handle with care, as the component can reach temperatures capable of causing skin burns during operation.