Skip to Content
  1. All products
  2. ⚡ Power & Management
  3. 4S 40A 18650 Lithium Battery Protection Board (BMS) – 14.8V/16.8V with Balance Charging for High-Power Drill Motors, Lipo Cells, and Robotics
  4. ⚡ Power & Management
मूल्य सूची: Retail Price (B2C) मूल्य सूची
मूल्य सूची: Retail Price (B2C) मूल्य सूची
4S 40A 18650 Lithium Battery Protection Board (BMS) – 14.8V/16.8V with Balance Charging for High-Power Drill Motors, Lipo Cells, and Robotics

4S 40A 18650 Lithium Battery Protection Board (BMS) – 14.8V/16.8V with Balance Charging for High-Power Drill Motors, Lipo Cells, and Robotics

(0 review)
ParameterDetailed Specification
Configuration4S (4 Cells in Series)
Nominal Voltage14.8V
Full Charge Voltage16.8V
Continuous Discharge CurrentMax 40A (Enhanced Heat Dissipation)
Continuous Charge CurrentMax 20A
Balance Current100mA
Protection FeaturesOvercharge, Over-discharge, Short-Circuit, Over-current
Application RangePower Drills, Motors, Inverters, Vacuum Cleaners
Price
₹ 101.69 ₹ 101.69
(Tax included)

Product Description

Upgrade your high-drain power tools and custom battery packs with the 4S 40A 18650 Lithium Battery Protection Board. This robust Battery Management System (BMS) is specifically engineered for high-current applications, supporting a continuous discharge of up to 40A. At Robogears, we recommend this "Balanced Version" for its ability to equalize the voltage across all four cells during the charging cycle, significantly extending the overall lifespan of your battery pack. Whether you are refurbishing a 14.8V cordless drill or building a high-torque robotic platform at your Pimpri facility, this BMS provides the industrial-grade safety and performance required to handle heavy motor startup currents without tripping.

Detailed Key Features

  • Integrated Balance Function: Automatically balances the voltage of each cell to 4.2V, ensuring maximum capacity utilization and preventing individual cell degradation.

  • High-Current Handling: Supports up to 40A continuous discharge, making it ideal for devices with high "inrush" currents like brushed and brushless DC motors.

  • Enhanced Thermal Management: Features a large surface area for heat dissipation, allowing the MOSFETs to stay cool even under consistent heavy loads.

  • Precision Overcharge/Discharge Protection: Safely cuts off power if any cell exceeds 4.25V or drops below 2.5V, protecting your expensive 18650 cells from permanent damage.

  • Start-up Pulse Support: Specifically tuned for power drills, allowing for the high initial current burst required to start a motor under mechanical load.

All Technical Details

  • Wiring Termination: Large solder pads for B+, B-, B1, B2, B3, and P+/P- to accommodate high-gauge silicon wires.

  • Standard Operating Temperature: -40°C to +85°C.

  • Internal Resistance: Less than 100mΩ, ensuring minimal voltage drop across the protection circuit.

  • Recovery Logic: Automatically recovers once the load is removed or the short-circuit condition is cleared.

Prototyping & Engineering Tips (Robogears Exclusive)

  • High-Current Wiring: At our Pimpri workshop, we suggest using 12AWG or 14AWG silicon wire for the P+ and P- connections. Standard thin jumper wires will melt or drop significant voltage when drawing 40A.

  • The "Zero Volt" Test: After soldering your 4 cells, if you see 0V at the output (P+/P-), connect a 16.8V charger for a few seconds. This "wakes up" the BMS from its shipping/safety lock mode.

  • Cell Matching: For best results, use four 18650 cells with the same internal resistance and capacity (mAh). If one cell is weak, the Balance function will take a very long time to equalize, or the BMS may cut off early.

  • Drill Compatibility: If your power drill "stutters" or stops immediately upon pulling the trigger, it means the motor's startup current is exceeding the 40A limit. Ensure your cells are "High Discharge" (10C or 20C rated) to support this BMS properly.

Package Includes

  • 1 x 4S 40A 18650 Lithium Battery Protection Board (Balanced Version)

Image Disclaimer

Product images are shown for illustrative purposes only. The color of the PCB (typically Green or Blue) or the specific brand of MOSFETs may vary between batches, but the 4S 40A balanced performance remains as described.