Skip to Content
  1. All products
  2. 🧠 Controllers & Systems
  3. 📡 Sensors & Modules
  4. PL2303HX USB to TTL UART RS232 Serial Adapter
  5. 📡 Sensors & Modules
मूल्य सूची: Retail Price (B2C) मूल्य सूची
मूल्य सूची: Retail Price (B2C) मूल्य सूची
PL2303HX USB to TTL UART RS232 Serial Adapter

PL2303HX USB to TTL UART RS232 Serial Adapter

(0 review)
SpecificationDetails
Main ChipProlific PL2303HX (Rev A)
Input InterfaceUSB Type-A Male
Output Interface5-Pin Header (3.3V, 5V, TXD, RXD, GND)
Logic LevelsDual 3.3V and 5V Power Output
Baud Rate Support75 bps to 12 Mbps
Supported OSWindows XP/7/8 (See Engineering Tips)
ProtectionOnboard 500mA Self-Recovery Fuse
Price
₹ 80.51 ₹ 80.51
(Tax included)

Product Description

The PL2303HX Serial Converter provides a stable and cost-effective way to add a virtual COM port to any PC. It features a standard USB Type-A plug on one end and five male header pins on the other, allowing for direct connection via jumper wires to your target board. The module is engineered with dual voltage outputs, enabling it to power small 3.3V sensors or 5V microcontrollers directly from the USB bus. Integrated TX and RX LED indicators provide immediate visual feedback of data transmission, which is critical for identifying communication errors during the initial stages of hardware development.

Key Features

  • Dual Power Output: Provides both 3.3V and 5V power pins, eliminating the need for an external power supply when programming low-power devices.

  • High-Speed Data: Supports a wide range of baud rates for everything from slow industrial sensors to high-speed firmware uploads.

  • Diagnostic LEDs: Includes onboard Transmit (TX) and Receive (RX) indicators that flash during active data exchange.

  • Over-Current Protection: Features a built-in fuse to protect your computer's USB port from accidental shorts on the target board.

  • Slim Form Factor: The narrow PCB design ensures it won't block adjacent USB ports on your laptop or hub.

Technical Details

  • Flow Control: Supports hardware flow control (RTS/CTS) depending on the specific driver and wiring configuration.

  • Compatibility: Works with standard terminal software like PuTTY, Tera Term, and the Arduino IDE Serial Monitor.

  • Housing: Transparent heat-shrink sleeve provides basic environmental protection.

Prototyping and Engineering Tips from Robogears

  • The "Cross-Wire" Rule: When connecting this to a microcontroller, always remember that TX (Transmit) on the module connects to RX (Receive) on the MCU, and RX on the module connects to TX on the MCU. If you connect TX to TX, no data will flow.

  • Driver Warning: The PL2303HX (Revision A) chip used in these modules may require a specific older driver version (v3.2.0.0) to work correctly on Windows 10 or 11. If you see a "Code 10" error in Device Manager, it is usually a driver compatibility issue rather than a hardware fault.

  • Programming the Pro Mini: To program a Pro Mini, connect the TX, RX, VCC, and GND. Note that most PL2303HX modules do not have a DTR pin for auto-reset. You will need to manually press the Reset button on your Pro Mini the moment the Arduino IDE status changes from "Compiling" to "Uploading."

  • Common Ground: Even if you are powering your target board from an external battery, you must connect the GND pin of this module to the GND pin of your target device. Without a shared ground, the signal levels will be unstable and data will be corrupted.

Package Includes

  • 1 x PL2303HX USB to TTL Serial Converter Module

Disclaimer

Ensure the voltage selection (3.3V or 5V) matches your target device's requirements before connecting the power pin. Applying 5V to a 3.3V-only device will result in immediate permanent damage to your hardware.