Skip to Content
  1. All products
  2. 🧠 Controllers & Systems
  3. 📡 Sensors & Modules
  4. 13.56MHz MIFARE Classic 1K RFID Contactless Smart Card for Access Control and Identity Management
  5. 📡 Sensors & Modules
Pricelist: Retail Price (B2C) Pricelist
Pricelist: Retail Price (B2C) Pricelist
13.56MHz MIFARE Classic 1K RFID Contactless Smart Card for Access Control and Identity Management

13.56MHz MIFARE Classic 1K RFID Contactless Smart Card for Access Control and Identity Management

(0 review)
FeatureDetails
Operating Frequency13.56 MHz (HF)
ProtocolISO/IEC 14443 Type A
Storage Capacity1KB (8k bit) EEPROM Memory
Read/Write Distance2cm to 10cm (Depends on Reader)
MaterialPremium Glossy White PVC
Data Retention10 Years
Price
₹ 20.00 ₹ 20.00
(Tax included)

Product Description The Thermoelectric Peltier Refrigeration Cooling System DIY Kit is a high-performance solid-state cooling solution designed for small-space air conditioning and electronic component cooling. Utilizing the powerful TEC1-12706 Peltier module, this kit functions by creating a significant temperature differential across its ceramic plates when 12V DC is applied. The assembly includes a large primary heat sink and a 90mm fan to dissipate heat from the "hot side," while a smaller heat sink and dedicated 40mm fan efficiently circulate chilled air from the "cold side." This pre-assembled kit is perfect for DIY pet house coolers, mini-refrigerators, medical insulin coolers, and laser diode temperature stabilization.

Key Features

  • Complete Cooling Solution: Includes the Peltier chip, two aluminum heat sinks, dual fans, and protective grilles for an out-of-the-box cooling experience.

  • Solid-State Reliability: No moving parts inside the cooling mechanism (excluding fans) means no vibration, no noise, and no refrigerant gases, making it eco-friendly.

  • Rapid Chill Performance: Capable of dropping the cold-side temperature significantly below ambient within minutes when properly insulated.

  • High-Efficiency Heat Dissipation: Large-surface-area aluminum fins paired with a high-flow 12V fan ensure the hot side remains within safe operating limits to maximize cooling delta.

  • Versatile Application: Compact footprint allows it to be integrated into incubators, PC cases, or small insulated boxes (up to 10 liters).

Technical Details

  • Thermoelectric Module: Features the TEC1-12706, an industrial-grade bismuth telluride based Peltier device with 127 couples.

  • Dual Fan Configuration: Large 12V fan handles the critical heat dissipation, while the small 12V fan prevents frost buildup by circulating air over the cold fins.

  • Heat Sink Design: Multi-fin extruded aluminum blocks maximize the contact surface area for both heat extraction and cold emission.

  • Thermal Interface: High-conductivity thermal grease pre-applied between the Peltier chip and heat sinks for minimum thermal resistance.

  • Wiring Setup: Simple two-wire configuration for the Peltier chip (Red +, Black -) and standard 2-pin connectors for the fans.

  • Current Management: Requires a stable 12V DC power source; the Peltier chip draws ~5A while fans draw ~0.2A each.

  • Cold Transfer: The cold side block is designed to be isolated from the hot side via a foam or plastic gasket (included) to prevent thermal leakage.

  • Environmental Safety: Operates without CFCs or compressors, making it safe for indoor and portable use.

  • Life Expectancy: Peltier module rated for over 100,000 hours of operation under normal conditions.

  • Maximum Temperature Delta: Achieves a Tmax of over 60°C (difference between the hot and cold plates).

  • Insulation Efficiency: Performance is highly dependent on the insulation quality of the space being cooled; best for 5L to 10L enclosures.

  • Material Build: High-grade 6063 Aluminum alloy for heat sinks and impact-resistant ABS plastic for fan housings.

  • Mounting Structure: Rigid screw-and-nut assembly ensures uniform pressure across the Peltier chip, essential for efficient heat transfer.

  • Logic Compatibility: Can be controlled via an Arduino using a high-current Relay or MOSFET for automated temperature control.

  • Standardization: Designed for 12V DC systems, fitting perfectly with automotive and industrial power rails.

Prototyping and Engineering Tips from Robogears

  • 9V Battery Use: Do not use a 9V battery. A standard 9V battery cannot provide the 5A to 6A current required. The Peltier will not cool and the battery will overheat. Use a 12V 10A DC Power Supply or a Car Battery.

  • 18650 Cell: You must use at least three 18650 cells in series (3S configuration). However, since the current draw is high, you need at least 3 strings in parallel (3S3P) with high-discharge cells (10A+ rating) and a 20A BMS.

  • IC & Capacitor Tip: For temperature control, use an STC-1000 Temperature Controller or an Arduino with a DS18B20 Sensor and a 30A Relay. Add a 4700uF 25V Capacitor across the 12V input to smooth out current spikes when the Peltier cycles on/off.

  • Related Products: We recommend pairing this with our 12V 10A SMPS Adapters, Digital Temperature Controllers, and Insulation Foam Sheets.

Package Includes

  • 1 x Thermoelectric Peltier Refrigeration Cooling System DIY Kit (Pre-assembled).

Disclaimer Image is for ilastration purpose only 2-3 lines. Never power the Peltier module without the hot-side heat sink and fan active; the chip will burn out in seconds. Ensure proper insulation between the cold and hot sections to prevent heat from bleeding back into the cooled space.