Skip to Content
  1. All products
  2. 🧠 Controllers & Systems
  3. 📡 Sensors & Modules
  4. 3.3V Adapter Board for 24L01 Wireless Module
  5. 📡 Sensors & Modules
Pricelist: Retail Price (B2C) Pricelist
Pricelist: Retail Price (B2C) Pricelist
3.3V Adapter Board for 24L01 Wireless Module

3.3V Adapter Board for 24L01 Wireless Module

(0 review)
FeatureDetails
Input Voltage5V DC
Output Voltage3.3V DC (Regulated)
Compatibility8-Pin nRF24L01+ and PA+LNA Modules
Connector2x4 Female Header Socket
Status IndicatorPower LED
Logic Support5V to 3.3V Logic Transitioning
Price
₹ 42.37 ₹ 42.37
(Tax included)

Product Description The 3.3V Adapter Board for NRF24L01 is a dedicated power management module designed to solve the common stability issues associated with high-power wireless transceivers. While the NRF24L01 operates strictly on 3.3V, it often suffers from communication failures when powered by the weak 3.3V rail of an Arduino. This adapter features an on-board AMS1117-3.3V regulator that allows you to power your wireless module from a stable 5V or even a 12V source. With integrated decoupling capacitors and a standard 2x4 female socket, it ensures a clean, ripple-free power supply for long-range, error-free wireless data transmission.

Key Features

  • Stable 3.3V Regulation: Converts unstable 5V-12V inputs into a precise 3.3V output specifically for the NRF24L01+ transceiver.

  • On-board Filtering: Features both SMD and electrolytic filtering capacitors to suppress power noise and prevent wireless signal dropping.

  • Plug-and-Play Socket: Equipped with a 2x4 (8-pin) female header, allowing the NRF24L01 module to be plugged in directly without messy wiring.

  • Power Indicator LED: Built-in SMD LED provides instant visual confirmation that the adapter is receiving power.

  • Enhanced Range Support: Provides the necessary current (up to 800mA) required for "PA+LNA" (Power Amplifier) versions of the NRF24L01, which the standard Arduino 3.3V pin cannot provide.

Technical Details

  • Voltage Conversion: Uses the AMS1117 LDO (Low Dropout) regulator to maintain 3.3V even as the input voltage fluctuates.

  • Input Range: Safely accepts DC voltages from 4.8V up to 12V, making it compatible with most industrial power rails.

  • Socket Pinout: standard NRF24L01 pinout (GND, VCC, CE, CSN, SCK, MOSI, MISO, IRQ).

  • Logic Transparency: The adapter regulates the power (VCC) only; the data lines (CSN, SCK, etc.) pass through directly to your microcontroller.

  • Current Capacity: Capable of delivering up to 800mA, far exceeding the 50mA limit of many onboard MCU regulators.

  • SMD Construction: Utilizes high-quality surface-mount components for a compact and vibration-resistant design.

  • Low Dropout Voltage: Requires only about 1.1V of "headroom" (Input voltage minus Output voltage) to function at peak current.

  • Heat Dissipation: The PCB is designed to act as a heat sink for the regulator during high-power wireless bursts.

  • PCB Finish: High-quality FR-4 with green solder mask and clear pin labeling for error-free installation.

  • Voltage Stability: Maintains less than 0.2% line regulation, essential for sensitive RF frequency stability.

  • Power Protection: Includes internal thermal overload and short-circuit current limiting.

  • Interface Compatibility: Works with standard NRF24L01 modules as well as the high-power SMA-antenna versions.

  • Wiring Simplification: Reduces the 8-pin wireless connection down to just 2 power pins (VCC/GND) and the standard SPI lines.

  • Logic Level Note: While it powers the module at 3.3V, the NRF24L01 pins are 5V tolerant, allowing direct connection to an Arduino Uno.

  • Capacitance Value: Optimized capacitor values (10uF) ensure fast transient response during the module's high-current transmission state.

Prototyping and Engineering Tips from Robogears

  • 9V Battery Use: This adapter is perfect for use with a 9V battery. You can connect the 9V battery directly to the adapter's VCC and GND pins; it will efficiently step it down to a safe 3.3V for your wireless module.

  • 18650 Cell: Two 18650 cells in series (7.4V) are an ideal power source for this adapter. For a single cell (3.7V), the voltage is too low for the regulator to function reliably; use a 5V Boost Converter before the adapter in that case.

  • IC & Capacitor Tip: Even with this adapter, for maximum range (PA+LNA modules), we recommend soldering an additional 10uF Tantalum Capacitor directly across the VCC and GND pins of the NRF24L01 module itself to further reduce RF noise.

  • Related Products: We recommend pairing this with our NRF24L01+ Wireless Transceivers, SMA 2.4GHz Antennas, and Arduino Nano boards.

Package Includes

  • 1 x 3.3V Adapter Board for NRF24L01 Wireless Module.

Disclaimer Image is for illustration purpose only 2-3 lines. Ensure the input voltage does not exceed 12V to avoid excessive heat on the regulator. Double-check the orientation of the NRF24L01 module before plugging it into the 8-pin socket to prevent pin misalignment.